3″ Round Double Offset Downspout – 2″ Clearance – One-Piece Seamless
Bypass Electrical Meters, Gas Lines, and Wall Obstructions | Leak-Free One-Piece Design | Aluminum S-Curve | Contractor and DIY | Damascus OR
CONTRACTOR LOCAL PICKUP – DAMASCUS, OREGON
Eliminate leak points and bypass wall obstructions with one professional fitting – no joint between elbows means no leak risk!
One-Piece Seamless Construction | 2″ Wall Clearance | Smooth S-Curve Water Flow | Standard Shipping Nationwide | Custom Orders Available
Stop leaks before they start. The GutterAll 3-inch round double offset is a one-piece aluminum fitting that clears electrical meters, gas lines, hose bibs, and other wall obstructions while eliminating the most common leak point in downspout systems. Unlike two separate elbows connected by a pipe section, the seamless S-curve construction removes the joint between fittings entirely – meaning no connection to fail, no seam to separate, and no leak to repair. The engineered 2-inch offset provides the clearance you need while maintaining optimal water flow through the smooth, continuous interior. For contractors who value professional results and homeowners who want long-term reliability, this one-piece design delivers what two-piece assemblies cannot: a leak-free obstruction bypass that looks better and lasts longer.
Clearance 2 Inches
Availability In Stock
Fulfillment Ship + Local Pickup
SKU GA-DS-3R-2OFF
Contractor Local Pickup: 19759 SE Sunnyside Rd, Damascus, OR 97089 – Mon-Fri 7am-4pm, Sat 8am-2pm PST | Phone: (503) 850-6784
Why One-Piece Double Offset Beats Two Separate Elbows
Eliminates the 1 Leak Point
Two-elbow assemblies require a joint between the fittings – and that joint is where leaks happen. The one-piece design removes this connection entirely. No joint means no leak point, no sealant to fail, and no repair needed years down the road.
Smoother Water Flow
The engineered S-curve creates a smooth, continuous path for water. No interior seam, no lip where debris catches, no turbulence where fittings meet. Water flows faster and cleaner through the seamless interior.
Cleaner Professional Appearance
One smooth fitting looks better than two elbows with a short pipe section between them. The clean S-curve profile presents a professional finished appearance that homeowners and property managers appreciate.
Faster Installation
One fitting instead of three pieces (elbow + pipe + elbow) means fewer connections to make, fewer fasteners to install, and less time on the ladder. Complete the obstruction bypass in half the installation time.
What Does 2 Inches of Clearance Clear?
The 2-inch offset provides adequate clearance for most standard wall-mounted obstructions:
Electrical Meters Standard residential meter boxes
Gas Lines Wall-mounted gas pipe runs
Hose Bibs Outdoor water spigots
Cable/Utility Boxes Wall-mounted junction boxes
Light Fixtures Wall-mounted exterior lights
Building Projections Minor ledges and trim
Need more clearance? We carry additional offset sizes. Call (503) 850-6784 to discuss your specific clearance requirements.
Technical Specifications
Double Offset Downspout / S-Curve Bypass Fitting
3 inches (round profile)
2 inches from wall
One-piece seamless (no mid-joint)
Baked-on enamel (UV-resistant)
Features and Benefits
- One-Piece Seamless Construction: Eliminates the leak-prone joint between two separate elbows
- Engineered S-Curve Profile: Provides 2-inch clearance while maintaining smooth water flow
- Bypass Wall Obstructions: Clears electrical meters, gas lines, hose bibs, and building projections
- Smooth Interior Flow Path: No internal seams or lips where debris can accumulate
- Baked-On Enamel Finish: UV-resistant coating for long-lasting appearance and protection
- Rust-Free Aluminum: No corrosion, no maintenance, decades of reliable service
- Professional Appearance: Clean S-curve looks better than two-elbow assemblies
- Faster Installation: One fitting instead of three pieces saves time on the ladder
- Standard 3″ Round Compatibility: Works with conventional 3-inch round downspout systems
- Residential and Commercial: Suitable for homes, apartments, offices, and commercial buildings
- Contractor Volume Pricing: Available for orders of 10+ units
- Same-Day Pickup: Available at Damascus, OR warehouse during business hours
Who Uses 3″ Round Double Offset Downspouts?
Contractors
- Gutter installation professionals
- Roofing contractors
- Property maintenance companies
- Commercial building contractors
- Renovation specialists
Benefit: Faster installation, fewer callbacks for leaks
DIY Homeowners
- Downspout system repairs
- Electrical meter bypasses
- New gutter installations
- Storm damage repairs
- Drainage improvements
Benefit: Professional results with simpler installation
Installation Guide – Contractors and DIY
- Verify system compatibility: Confirm your downspout is 3-inch round diameter (not 2×3″ rectangular)
- Measure clearance needed: Measure from wall face to center of obstruction to confirm 2″ is adequate
- Position the offset: The S-curve moves the downspout 2″ away from the wall, then back parallel
- Connect upper end: Slide the upper end onto the downspout section above the obstruction
- Secure with fasteners: Use 2-3 pop-rivets or sheet metal screws at each connection
- Apply sealant: Use lap-joint sealant at connections for water-tight seal
- Connect lower end: Attach the lower downspout section to continue the run
- Test drainage: Run water through the system to verify proper flow
Pro Tip: The one-piece design means you only have two connections to make instead of four with a two-elbow assembly. Position fasteners on the back side where they’re less visible from ground level.
Why GutterAll
Contractor Direct Pricing
We sell direct to contractors and homeowners at competitive prices. Volume pricing available for orders of 10+ units.
Same-Day Warehouse Pickup
Pick up in-stock items same day at 19759 SE Sunnyside Rd, Damascus, OR. No waiting when the job is ready now.
Nationwide Shipping
Ships to all 50 states from our Damascus, OR warehouse. Orders typically process within 1-2 business days.
Expert Support
Call or email our team to confirm fit, discuss volume needs, or coordinate local delivery. We know gutter systems.
Frequently Asked Questions
Why choose a one-piece double offset over two separate elbows?
A one-piece double offset eliminates the connection joint between two elbows – and that joint is where leaks happen most often. The seamless S-curve also provides smoother water flow, faster installation, and a cleaner finished appearance compared to two separate fittings joined with a pipe section.
Will this fit my existing 3-inch round downspout?
Yes. This offset is designed for standard 3-inch round downspout systems using conventional slip-joint or pop-rivet fastening. Confirm your system is 3-inch round (not 2×3-inch rectangular) before ordering. If unsure, measure the inside diameter of the downspout opening.
Is 2 inches of clearance enough for my obstruction?
A 2-inch offset clears most standard obstacles including electrical meters, gas lines, hose bibs, and minor building projections. Measure your specific clearance requirement before ordering. If you need more clearance, call (503) 850-6784 – we carry additional offset sizes.
Can this be shipped or is local pickup only?
Both options are available. This product ships to all 50 states. Local pickup is also available at 19759 SE Sunnyside Rd, Damascus, OR 97089, Monday-Friday 7am-4pm and Saturday 8am-2pm PST. Local delivery can also be arranged in the Portland Metro area – call (503) 850-6784 to coordinate.
Do you offer contractor or volume pricing?
Yes. Orders of 10 or more units qualify for volume pricing. Contact us at (503) 850-6784 or [email protected] to discuss your project requirements and get a quote.
Custom Orders Welcome!
Need different offset clearances, bulk contractor quantities, or complete downspout component packages? We can help!
Our team works with contractors and homeowners on custom orders including different offset sizes (more or less than 2″), high-volume contractor quantities, and complete downspout system packages. Whether you’re outfitting a large commercial project or need a specific clearance for your home, contact us to discuss your requirements.
Contact Us for Custom Orders: (503) 850-6784
Or email: [email protected]
GutterAll – Your Gutter Component Specialist
Professional gutter components for contractors and DIY homeowners since 2010
Address 19759 SE Sunnyside Rd
Damascus, OR 97089
Hours Mon-Fri: 7am-4pm
Sat: 8am-2pm PST
Phone (503) 850-6784
Email [email protected]
